|
Request
for Quotation
NOMINAL DATA SHEET
|
|
| NI - 99.0%min |
Food Processing Equipment |
| C - .15%max |
Electrical & Electronic
Parts |
| MN - .35%max |
Aerospace Components |
| S - .010%max |
Rocket Motor Casings |
| SI - .35%max |
Transducers |
| CU - .25%max |
|
| FE - .40% |
|
| |
Top of Page
| PHYSICAL
PROPERTIES (ANNEALED CONDITION) |
| Modulus of Elasticity, Tension
10(******)psi - 29.6 |
| Magnetic permeability at
200H(At 70 F) - 110-600 |
| Electrical Resistivity,
Microhm-cm(At 70 F) - 9.5 |
| Density, lb/cu.in. - .321 |
| Coefficient of Thermal
Expansion, in./in./ F x 10(-******) |
| 70 - 200 F ............................
7.4 |
| 70 - 400 F ............................
7.7 |
| 70 - 800 F ............................
8.3 |
| 70 - 1000 F ...........................
8.5 |
| |
| NOMINAL
MECHANICAL PROPERTIES (ANNEALED CONDITION) |
| Ultimate Tensile Strength, psi - 72,000 |
| 0.2% Offset Yield Strength,
psi - 25,000 |
| Elongation in 2 inches
percent - 40 |
| Density, lb/cu.in. - .321 |
| Hardness, Rockwell - B61 |
| |
Top of Page
NOMINAL DATA SHEET
|
|
| NI - 99.0%min |
Heat Exchanger Parts |
| C - ..02%max |
Electrical Parts |
| MN - .35%max |
Aerospace Components |
| S - .010%max |
|
| SI - .35%max |
|
| CU - .25%max |
|
| FE - .40% |
|
| |
Top of Page
| PHYSICAL
PROPERTIES (ANNEALED CONDITION) |
| Modulus of Elasticity, Tension
10(******)psi - 30 |
| Magnetic permeability at
200H(At 70 F) - 110-600 |
| Electrical Resistivity,
Microhm-cm(At 70 F) - 8.4 |
| Density, lb/cu.in. - .321 |
| Coefficient of Thermal
Expansion, in./in./ F x 10(-******) |
| 70 - 200 F ............................
7.3 |
| 70 - 400 F ............................
7.7 |
| 70 - 800 F ............................
8.4 |
| 70 - 1000 F ........................... |
| |
| NOMINAL
MECHANICAL PROPERTIES (ANNEALED CONDITION) |
| Ultimate Tensile Strength, psi - 59,000 |
| 0.2% Offset Yield Strength,
psi - 15,000 |
| Elongation in 2 inches
percent - 40 |
| Hardness, Rockwell - B55 |
| |
| Coil
Slit
to your width |
Sheet
Length
60" |
Rod
diameter |
|
TK
.003"
.004"
.005"
.010"
.015"
.020"
.030"
.040"
.062" |
TK
WIDTH
.003" x 12"
.004" x 12"
.005" x 12"
.010" x 12"
.015" x 12"
.020" x 12.5" |
.050"
.250"
.375"
.500"
.750"
1.0"
1.5" |
Most common diameters
Most common sheet thicknesses nickel plate also available.
Ni 270 available on special
request.
Top of Page
Disclaimer
Every
effort is made to ensure that technical specifications are accurate.
However, technical specifications included herein should be used as a
guideline only. All specifications are subject to change without notice.
|
