|
Request
for Quotation
COPPER ALLOYS 101 / 102 / 110
| AVAILABLE SIZES |
| COPPER
101 NOMINAL
DATA SHEET |
| CHEMICAL COMPOSITION:
99.99% CU min./.0003 PH |
| ASTM ALLOY
NO.: B152 |
| FEDERAL SPECS.:
QQC576 |
| DENSITY(lbs. per cu. in
at 68 F (Annealed) (x 27.68 = gms/cu cm at 20 C):.322 |
| MOD. OF ELAST.(x
10****** PSI, tension):17 |
| ELECT. COND.(% IACS at
68 F (20 C) as annealed):101 |
| THERM. COND. |
| (BTU per sq.ft.per
ft.per hr.per F at 68 F,(20 C):226 |
COEFF.OF TH.EXPN.
(Inches/inch/ F x 10(-******) from 68 F to 572 F
(20 C to 300 C):9.8 |
| |
|
COPPER
101
TENSILE STRENGTH
|
|
| YIELD STRENGTH(0.2% offset) |
|
|
| (x 1000 PSI
(MPA = KSI x 6.8948) |
| annealed: 26
- 38 |
8 - 14 |
| 1/2 hard: 37
- 46 |
30 - 44 |
| full hard:
43 - 52 |
41 - 50 |
| spring: 50 - 58 |
48 - 57 |
| |
Top of Page
|
ELONGATION % in 2 inches(= % in 50mm)
|
annealed: 20 - 50
1/2 hard: 8 - 32
full hard: 3 - 16
spring: 2 - 4 |
|
| |
|
ROCKWELL B HARDNESS
(.020 gauge and over (Rockwell F or 30 T where noted)
|
annealed:
1/2 hard: 77 - 89(F)
full hard: 86 - 93(F)
spring: 91 - 97(F) |
|
| |
| NOMINAL
DATA SHEET |
| CHEMICAL COMPOSITION:
99.95 CU min./.015-.040 P |
| ASTM ALLOY
NO.: B152 |
| SAE ALLOY NO.: CA122 |
| FEDERAL SPECS.:
QQC576 |
| DENSITY(lbs. per cu. in
at 68 F (Annealed) (x 27.68 = gms/cu cm at 20 C):.323 |
| MOD. OF ELAST.(x
10****** PSI, tension):17 |
| ELECT. COND.(% IACS at
68 F (20 C) as annealed):101 |
| THERM. COND. |
| (BTU per sq.ft.per
ft.per hr.per F at 68 F,(20 C):196 |
COEFF.OF TH.EXPN.
(Inches/inch/ F x 10(-******) from 68 F to 572 F
(20 C to 300 C):9.8 |
| |
Top of Page
|
|
| YIELD STRENGTH(0.2% offset) |
|
|
| (x 1000 PSI
(MPA = KSI x 6.8948) |
| annealed: 26
- 38 |
8 - 14 |
| 1/2 hard: 37
- 46 |
30 - 44 |
| full hard:
43 - 52 |
41 - 50 |
| spring: 50 - 58 |
48 - 57 |
| |
|
ELONGATION % in 2 inches(= % in 50mm)
|
annealed: 20 - 50
1/2 hard: 8 - 32
full hard: 3 - 16
spring: 2 - 4 |
|
| |
|
ROCKWELL B HARDNESS
(.020 gauge and over (Rockwell F or 30 T where noted)
|
annealed:
1/2 hard: 77 - 89(F)
full hard: 86 - 93(F)
spring: 91 - 97(F) |
|
| |
| NOMINAL
DATA SHEET |
| CHEMICAL COMPOSITION:
ETP COPPER 99.90 CU min./.05 OXYGEN Max. |
| ASTM ALLOY
NO.: B152 |
| SAE ALLOY NO.: CA110 |
| FEDERAL SPECS.:
QQC576 |
| DENSITY(lbs. per cu. in
at 68 F (Annealed) (x 27.68 = gms/cu cm at 20 C):.322 |
| MOD. OF ELAST.(x
10****** PSI, tension):17 |
| ELECT. COND.(% IACS at
68 F (20 C) as annealed):101 |
| THERM. COND. |
| (BTU per sq.ft.per
ft.per hr.per F at 68 F,(20 C):226 |
COEFF.OF TH.EXPN.
(Inches/inch/ F x 10(-******) from 68 F to 572 F
(20 C to 300 C):9.8 |
| |
Top of Page
|
|
| YIELD STRENGTH(0.2% offset) |
|
|
| (x 1000 PSI
(MPA = KSI x 6.8948) |
| annealed: 26
- 38 |
8 - 14 |
| 1/2 hard: 37
- 46 |
30 - 44 |
| full hard:
43 - 52 |
41 - 50 |
| spring: 50 - 58 |
48 - 57 |
| |
|
ELONGATION % in 2 inches(= % in 50mm)
|
annealed: 20 - 50
1/2 hard: 8 - 32
full hard: 3 - 16
spring: 2 - 4 |
|
| |
|
ROCKWELL B HARDNESS
(.020 gauge and over(Rockwell F or 30 T where noted)
|
annealed:
1/2 hard: 77 - 89(F)
full hard: 86 - 93(F)
spring: 91 - 97(F) |
|
| |
CDA 101, CDA 102, ETP Copper 110
COPPER ALLOYS 101/102/110
|
COIL and FOIL |
|
.003
.004
.005
.010
.015
.020
.032
.040
.050
.062 |
*NOTE: Other sizes available upon request.
Top of Page
Disclaimer
Every
effort is made to ensure that technical specifications are accurate.
However, technical specifications included herein should be used as a
guideline only. All specifications are subject to change without notice.
|
